Pro AV Catalog
Manufacturers
PRODUCT CATEGORIES
Matching Keywords
Model Numbers
Request Quote
All Products
Vocia® Amplifier (VA-8600)
Series: Vocia®
Model: Vocia VA-8600
Part #: 0267.900
- Modular based design
- Amplification modules have software configurable power levels/load options
- -8 amplification modules per frame with 100 to 600 Watts per module (maximum of 2400W per chassis)
- -70V or 100V with direct drive capability, or low-impedance (4 or 8 ohms) operation
- -Maximum of 2400 Watts of power in a device
Product Info
Tech Specs
Documents
Videos
The VA-8600 is a digital networked multi-channel amplifier for use in Vocia® systems. The VA-8600 is CobraNet® enabled and features eight channels of modular amplification and DSP with optional channel-to-channel or device-to-device failover. It can support up to eight amplifier cards that are individually software configurable from 100600 Watts for up to 2400 Watts of power per chassis. 70V, 100V and low-impedance outputs are software selectable per card. The on-board DSP provides comprehensive fixed-chain digital-signal processing within the device, including volume control, ducking, equalization, compressor/limiter, speaker crossover, delay, and output gain. Emergency messages for life-safety compliant systems are stored in non-volatile memory within the VA-8600. Intuitive software provides audio system design via PC. Two RJ45 connectors on the rear panel of the VA-8600 provide redundant connectivity to control data and audio over a single Ethernet cable.
- Modular based design
- Amplification modules have software configurable power levels/load options
- -8 amplification modules per frame with 100 to 600 Watts per module (maximum of 2400W per chassis)
- -70V or 100V with direct drive capability, or low-impedance (4 or 8 ohms) operation
- -Maximum of 2400 Watts of power in a device
- Failover capability between channels and amplifiers
- Local non-volatile storage of emergency messages
- LED Indication:
- -Amplifier failure
- -Clip present
- -Fan stuck-rotor
- -Heat sink temperature fault
- -Signal Peak
- -Signal present
- Software Monitoring Features:
- -Amplifier failure
- -Excessive clipping
- -Fan stuck rotor
- -Heat sink temperature fault
- -Peak present
- -Short circuit on output
- Software-configurable signal processing including volume control, filters, compressor/limiting, delay, speaker equalization, and output sensitivity
- CobraNet audio and control data over a single Ethernet cable
- Dual Ethernet ports for redundancy
- Heavy duty removable terminal block connectors for speaker line connections
- Rotary switches for unit identification
- Rack mountable (3RU)
- CE marked, UL listed & RoHS compliant
- Covered by Biamp Systems' warranty
- Spec Sheet available - Yes
- Height: 5.25 inches (133mm)
- Width: 19 inches (483mm)
- Depth:
17.25 inches (438mm)
- Depth: 17.25 in
- Height: 5.25 in
- Width: 19 in
- Product Weight: 50 lbs
- Operating Temperature (Maximum): 107 F
- Operating Temperature (Minimum): 18 F
- Maximum Frequency Response (Bandwidth): 20 kHz
- Maximum Frequency Response (Bandwidth): 20000 Hz
- Minimum Frequency Response (Bandwidth): 20 Hz
- Minimum Frequency Response (Bandwidth): 0.02 kHz
- Memory: 5.625 MB
- Inputs:
20 bits, 48 kHz, 5-1/3 ms (fixed)
- Connection:
RJ45 with shielded Ethernet/PoE cable (Cat5, Cat5e, Cat6 or Cat7)
- Total Output Power:
2400W maximum per chassis (Burst Mode only. Protective thermal limiting will reduce long-term power output
- Environment:
- Ambient Operating:
- Ambient intake humidity: 0 - 100% non-condensing
- Altitude:
0 - 10,000 Feet MSL
- Power:
110-120 & 220-240VAC 50/60Hz
- Chassis Weight: 50 lbs. (22.68 kg)
- AM 600 card Weight:
1.25 lbs. (0.57 kg)
- Compliance:
EU Directive 2002/95/EC, RoHS Directive
UL listed
CE marked
- Supported Loads: 4 ohms, 6 ohms, 8 ohms, 70-Volt or 100-Volt Line direct drive
- Frequency Response: 20 Hz - 20 kHz frequency response flat +/-1 dB
- Continuous operation in chassis with fans running normally and unrestricted intake and exhaust:
600 W: 1 kHz continuous sine wave indefinitely
- Distortion and Noise:
< or equal to 0.3% THD+N (20 Hz - 20k Hz) all loads and power levels
- Intermodulation Distortion (SMPTE):
<0.2%
- Inter-channel Isolation: >75 dB (20 Hz-20 kHz, full power out)
- DC Offset: <10mV
Vocia_Sales_Sheet_Feb10.pdf
5667 kb
- Other
Vocia VA-8600 brc (1Feb10).pdf
1042 kb
- Other
Revit file for Vocia VA-8600
3432 kb
- BIM Objects
Vocia Product Catalog
9064 kb
- Brochure
biamp_data_sheet_vocia_va-8600_jan22.pdf
527476 kb
- Data Sheet
Request Quote
Thank you!
Someone will be in touch with you shortly.
Contact Create Spaces
close
Create Spaces
623 S Americana Blvd, Boise, ID 83702
Boise, ID 83702
USA
2083850507
https://createspaces.com/
Contact in regards to this product:
Biamp
Model: Vocia VA-8600
Request more information from a dealer near you
close
Request more information from a dealer near you