Wireless In-Ceiling Switch, 230VAC
Series: Pyng/Green Light
Model: CLCI-1SW2EX-W
Part #: 6503840
- 2-channel switch for 230VAC lighting loads
- Provides control of lighting fixtures
- Compact surface-mount design for new or retrofit applications
- Two independently-controlled zone outputs
- No special wiring—installs inline at the device
The CLCI-1SW2EX-W is a two-channel switch capable of controlling two independent, 230VAC lighting loads. Its ultra-slim design allows it to be installed in the ceiling, either next to or near the fixture. The CLCI-1SW2EX-W communicates with the Crestron control system using infiNET EX® wireless technology, making it perfect for both new and retrofit applications.
The CLCI-1SW2EX-W installs inline without requiring special wiring and can be controlled via a standard light switch.
Two-Channel Switching
The CLCI-1SW2EX-W switches incandescent, tungsten-halogen, magnetic low-voltage, electronic low-voltage, fluorescent ballast, neon/cold cathode, and motor loads for each of the two independent channels. Two sets of screw terminals (internally wired in parallel) enable easy wiring to each load of up to 500 VA.
Easy Loop-Thru Wiring
The CLCI-1SW2EX-W is powered using a set of high-voltage screw terminals and has a second set of terminals that are wired in parallel to easily daisy-chain additional CLCI-series devices. This provides a fast, clean installation when deploying multiple CLCI- devices and eliminates the need for additional wire connectors or extra gang boxes. In some retrofit applications, this lets you create more zones from what was originally wired.
Out-of-the-Box Control via Standard Switch
The CLCI-1SW2EX-W provides built-in support for applications that require basic load control using a cost effective maintained or momentary switch to control the load. Use a maintained or momentary switch to perform basic on and off control.
Complete Crestron Control
A Crestron control system connection allows the CLCI-1SW2EX-W to be controlled from any keypad, touch panel, remote, or mobile device. Tie in occupancy sensors and photocells together with Crestron Fusion® software for a complete solution to effectively manage energy.
Simple Setup
Setup is simple, especially when using a connected maintained or momentary switch. A specific series of button presses initiates the wireless device acquire mode, so there's no need to climb a ladder to join the device to the infiNET EX network.
- 2-channel switch for 230VAC lighting loads
- Provides control of lighting fixtures
- Compact surface-mount design for new or retrofit applications
- Two independently-controlled zone outputs
- No special wiring—installs inline at the device
- Rated 500 VA load capacity per channel
- infiNET EX® wireless communication ensures reliable operation
- Local controls for setup
- Built-in support for control via standard momentary or maintained switch
- Setup via on-board button or connected switch
- Daisy-chain units for easy deployment
- Operates using 220-240VAC power
- Captive screw terminal connections
- Spec Sheet available - Yes
- Operating Temperature (Maximum): 104 F
- Operating Temperature (Minimum): 32 F
- AC Voltage: 240 Volts
- Product Weight: 0.44 lbs
- Depth: 1.61 in
- Height: 7.01 in
- Width: 2.17 in
- Load Ratings:
- Number of Channels: 2
- Maximum Load per Channel: 2AX (2A fluorescent)
- Switch Load Types: Incandescent, tungsten-halogen, magnetic low-voltage, electronic low-voltage, fluorescent ballast, neon/cold cathode, motor
- Wireless Communications:
- RF Transceiver:infiNET EX® 2-way RF, 2.4 GHz ISM channels 11-26 (2400 to 2483.5 MHz), default channel 15; IEEE 802.15.4 compliant
- Range:
- 30 m (100 ft) indoors, 55 m (175 ft) outdoors for device to device;
- 45 m (150 ft) indoors, 75 m (250 ft) outdoors for device to gateway;
- All distances subject to site specific conditions[1]
- Gateway:Requires an infiNET EX gateway[2]
- Connections:
- L: (3) Screw terminals, connect to line AC; Internal wiring in parallel
- N: (2) Screw terminals, connect to neutral AC; Internal wiring in parallel
- G: (2) Screw terminals, connect to earth ground; Internal wiring in parallel
- R: (1) Screw terminal, connects to remote switch (remote switch wires to L and R; Consult manual for more information)
- N1: (1) Screw terminal, neutral, channel 1
- SL1: (1) Screw terminal, switched line power, channel 1
- N2: (1) Screw terminal, neutral, channel 2
- SL2:(1) Screw terminal, switched line power, channel 2
- Controls & Indicators:
- Setup:(1) Miniature pushbutton, joins an infiNET EX network
- Chan. 1: (1) Green LED, indicates load is switched on
- Chan. 2: (1) Green LED, indicates load is switched on
- Enclosure: Plastic
- Environmental:
- Humidity:10% to 90% RH (non-condensing)
- NOTES:
- Any infiNET EX device that provides expander functionality will effectively extend the range of the wireless network beyond the initial range of the gateway. Battery-powered infiNET EX devices do not provide expander functionality.
- Item(s) sold separately.
Create Spaces
623 S Americana Blvd, Boise, ID 83702
Boise, ID 83702
USA
2083850507
https://createspaces.com/