8-channel 277V Dimmer Module with Terminal Block, 2 Feeds
Model: GL-CAEN-2DIMFLV8-277 KIT
- Eight-channel 0-10V dimmer module for commercial lighting applications
- Installs in a Crestron® CAEN enclosure
- Supports 0-10V dimmable fluorescent ballasts and LED drivers
- Also supports on/off switching of non-dimmable lighting loads
- Single or dual feeds — two four-channel dimmers in one module
Provides eight channels of dimming for commercial lighting applications. Supports 0-10 Volt dimmable fluorescent ballasts and LED drivers. May also be used to switch non-dimmable lighting loads. Installs in a CAEN wall mount automation enclosure as part of a complete Crestron® centralized lighting control system.
The Crestron® GL-CAEN-2DIMFLV8-277 is an eight-channel, two-feed dimmer module designed for 277V commercial lighting system applications. It installs in a CAEN enclosure and provides control of 0-10 Volt dimmable fluorescent ballasts and LED drivers. It can also be used to switch non-dimmable lighting loads. Dual feed capability provides two independent four-channel dimmers in one module space. Each output channel is rated for 16 Amps, with a total module rating of 32 Amps when fed from two separate 20 Amp feeds.
Emergency Lighting Control
The GL-CAEN-2DIMFLV8-277 is UL® 924 and CSA® C22.2 No. 141-15 listed for use in controlling emergency lighting loads. In the event of a power failure, a contact closure from a power loss sensor (Crestron GLS-PLS-120/277, sold separately) activates the override mode in the GL-CAEN-2DIMFLV8-277 to turn on each designated lighting load if it is off (assuming line power is supplied by a backup power source). The override dimming level can be preset to any value when commissioning the lighting system, so even if the load is already on prior to a power failure, it will change to the preset level when override mode is activated.
Centralized Lighting Cabinet Installation
Crestron GL-CAEN series commercial lighting control modules are designed to be installed in a CAEN wall mount enclosure. Available in a variety of sizes, CAEN enclosures provide a scalable, high-density centralized lighting control solution for any-sized commercial building or facility. A selection of GL-CAEN module types is offered to accommodate a wide range of load types and system configurations.
- Eight-channel 0-10V dimmer module for commercial lighting applications
- Installs in a Crestron® CAEN enclosure
- Supports 0-10V dimmable fluorescent ballasts and LED drivers
- Also supports on/off switching of non-dimmable lighting loads
- Single or dual feeds — two four-channel dimmers in one module
- Rated 16 Amps per channel, 32 Amps total (using two 20 Amp feeds), at 277 Volts AC
- Customizable dimming curves via software
- Arcless switching
- Built-in air gap relay per channel
- Closure-activated override mode
- UL® 924 and CSA® C22.2 No. 141-15 listed for emergency lighting control
- Crestron system integration via Cresnet®
- Includes terminal block for high-voltage wiring
- CEC Title 24 2013 compliant
- Spec Sheet available - Yes
- Operating Temperature (Maximum): 104 F
- Operating Temperature (Minimum): 32 F
- Certifications: CE, UL, FCC
- AC Voltage: 277 Volts
- Depth: 3.32 in
- Height: 7.53 in
- Width: 6.91 in
- Product Weight: 3.15 lbs
- Load Control:
•Dimmer Channels: 8
•Dimmable Load Types: 0-10 Volt fluorescent ballasts or LED drivers (4-wire)
•Switched Load Types: LED, incandescent, fluorescent, magnetic low-voltage, electronic low-voltage, high-intensity discharge (HID)
•Per Channel Load Rating: 16 Amps
•Per Group Load Rating: Group 1 (Channels 1-4): 16 Amps
•Group 2 (Channels 5-8): 16 Amps
•Module Total Load Rating: 32 Amps
•Line/Load Voltage: 277 Volts AC, 50/60 Hz requires one or two single-phase feeds (may be same or different phases)
• 0-10V Output: 0-10 Volts DC, 100 mA maximum per channel, sink or source - Connections:
•Via Terminal Block (included): LINE 1 - 2: (2) Screw terminals, black, line power feed inputs (per group)
•SW 1 - 8: (8) Screw terminals, red, switched load outputs (per channel)
•N IN 1 - 2: (2) Screw terminals, white, line power feed neutrals (per group)
•N OUT 1 - 8: (8) Screw terminals, white, load neutrals (per channel)
•Note: Each terminal accepts one 14-10 AWG wire.
•1 - 8: (8) 2-pin detachable terminal blocks
•0-10 Volt dimming control outputs
•26 to 12 AWG (0.14 to 2.5 mm²) wire size
•For use with Class 1 or Class 2 wiring
•Module Interconnect: (2) 5-pin 0.156 inch headers
•Cresnet/Override interconnect ports
•Each connects to the adjacent module using the interconnect jumper provided
•Connects to a CAEN-BLOCK (sold separately) when installed in the lowest position within the enclosure - Controls and Indicators:
•PWR: (1) Green LED, indicates line power is applied to the LINE 1 terminal
•NET: (1) Yellow LED, indicates Cresnet communication with the control system
•SETUP: (1) Pushbutton and (1) red LED for Cresnet setup using TSID (Touch Settable ID)
•1 - 8: (8) Pushbuttons and (8) red LEDs, each pushbutton toggles the corresponding channel on and off (press and hold to cycle the dimming level up and down), each LED indicates the corresponding load output is energized - Environmental:
•Humidity: 10% to 90% RH (non-condensing)
•Heat Dissipation: 45 BTU/hr - Enclosure:
•Gray metal, surface mount module with (2) integral mounting flanges
•Occupies 1 module space in a CAEN enclosure
Create Spaces
623 S Americana Blvd, Boise, ID 83702
Boise, ID 83702
USA
2083850507
https://createspaces.com/