Fiber Optic Systems : Fiber Optic Receivers & Transmitters : AMX - DXF-RX-MMS

DXLink HDMI Multimode Simplex Fiber Receiver

Model: DXF-RX-MMS

Part #: FG1010-563

Only One Cable – Send audio and video, while passing power over one twisted pair cable
Multi-Format Analog Port and HDMI Port – Supports legacy analog signals - RGBHV, Component, S-Video, and Composite, and digital HDMI/HDCP, DisplayPort++ and DVI signals
Send HDMI signals up to 100 meters – Extend the reach of the HDMI signals far beyond the capabilities of typical HDMI cabling
Standard Twisted Pair Cable – Save time and effort in installation by leveraging cost effective twisted pair cable, see the Cabling for Success with DXLink white paper for more details
Easy Installation – Mounts in standard decor style wallplates

More Product Information Below

Compare

Project List

Product Info

Tech Specs

Documents

OVERVIEW

The DXLink HDMI Fiber Receiver features built-in SmartScale® Technology to deliver HDMI with HDCP that is perfectly scaled for each connected display automatically, eliminating the integration challenges that can occur when sources and displays have different optimal resolutions. It accepts audio and video over multimode fiber from up to 300 meters. Mount the low-profile DXLink Fiber Receiver behind a display or above a ceiling mounted projector.

COMMON APPLICATIONS

The ideal solution for any destination display or projector designed into an Enova DGX integrated system that requires the distance capabilities and inherent security of fiber – or both; including campus-wide distribution of sources that are shared between classrooms, secure military applications, casinos, arenas and museums. Directly connect LCDs, plasmas and projectors using the HDMI output connection while delivering room audio via the stereo audio output.

Only One Cable – Send audio and video, while passing power over one twisted pair cable
Multi-Format Analog Port and HDMI Port – Supports legacy analog signals - RGBHV, Component, S-Video, and Composite, and digital HDMI/HDCP, DisplayPort++ and DVI signals
Send HDMI signals up to 100 meters – Extend the reach of the HDMI signals far beyond the capabilities of typical HDMI cabling
Standard Twisted Pair Cable – Save time and effort in installation by leveraging cost effective twisted pair cable, see the Cabling for Success with DXLink white paper for more details
Easy Installation – Mounts in standard decor style wallplates
Power over DXLink

Enabled – Designed for use with Enova DGX or DVX systems with DXLink inputs, or PS-POE-AT-TC (FG423-84) or PDXL-2 (FG1090-170) to provide remotely located Power over DXLink (requires firmware v1.2.40 or above)
DXLink Direct Connection – When receiving Power over DXLink
from the PS-POE-AT-TC or PDXL-2, DXLink Wallplates can be connected directly to a DXLink Receiver for a point-to-point solution
Power Remotely - Power over DXLink is carried over twisted pair to simplify installation when used with the Enova DGX, Enova DVX, PS-POE-AT-TC or PDXL-2
3D Support - Pass through latest video formats including 3D and Deep Color
Surround Sound Support - Pass through high definition surround sound including Dolby TrueHD, DTS-HD Master Audio, Dolby Digital, DTS and 2-channel through 8-channel L-PCM at 32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192kHz
HDCP Compliant
DEALER BENEFITS
- HDMI/HDCP With Simplicity of Analog - Hassle-free plug-and-play operation eliminates the need for time-consuming cumbersome work-around tools to deal with HDCP key constraints and resolution incompatibilities
- Installation Friendly - Standard two gang size and remote powering capabilities allows the wallplate to be installed in virtually any location
- Complements Any Environment - Decor Wallplate is available in black or white and blends well in both commercial and residential applications
CUSTOMER BENEFITS
- Interruption-Free Content - Exclusive InstaGate Pro® Technology allows audio and video to be switched quickly and easily to every connected display without the difficulties typically associated with HDCP
- Easily Connect Guest Devices - Provides a versatile solution for environments where sources are consistently changing

Fiber Optic Connector Type - LC-LC
Fiber Optic Signals Supported - Audio
Fiber Optic Signals Supported - DVI
Fiber Optic Signals Supported - HDMI
ROHS Compliant - Yes
Warranty - Yes
Spec Sheet available - Yes

Regulatory Compliance: HDCP, WEEE
Operating Temperature (Maximum): 104 F
Operating Temperature (Minimum): 32 F
Certifications: FCC, CE, UL
AC Voltage (Maximum): 240 Volts
AC Voltage (Minimum): 100 Volts
Active Power: 20 Watt
Current Draw: 0.80 Amps
Depth: 5.25 in
Height: 1 in
Width: 8.75 in
Product Weight: 1.10 lbs
Shipping Weight: 2.20 lbs
Noise: 45.3 dBA
Signal to Noise Ratio: 93 dB
Warranty (Length/Type): 3 Years Limited
General:
- MTBF: 124,232 hours
- Noise Level: 0 dBA @ 1m (typ), 45.3 dBA @ 1m (max)
- Airflow: Convection (openings on top of case, typ), forced air (out of front plate, when fan is active) Mounting Options: Compatible V Style mounting options
  - AVB-VSTYLE-RMK-FILL-1U, V Style Module Rack Mounting Tray with Fill Plates (FG1010-721)
  - AVB-VSTYLE-RMK-1U, V Style Module Rack Mounting Tray (FG1010-720)
  - AVB-VSTYLE-SURFACE-MNT, V Style Single Module Surface Mount Brackets (FG1010-722)
  - AVB-VSTYLE-POLE-MNT, V Style Single Module Pole Mounting Kit (FG1010-723)
- Included Accessories: Ships with a desktop power supply with power cord
- Optional Accessories:
  - AVB-VSTYLE-RMK-FILL-1U, V Style Module Rack Mounting Tray with Fill Plates (FG1010-721)
  - AVB-VSTYLE-RMK-1U, V Style Module Rack Mounting Tray (FG1010-720)
  - AVB-VSTYLE-SURFACE-MNT, V Style Single Module Surface Mount Brackets (FG1010-722)
  - AVB-VSTYLE-POLE-MNT, V Style Single Module Pole Mounting Kit (FG1010-723)
  - CC-NIRC, NetLinx IR Emitter Cable (FG10-000-11)
  - IR03, External IR Receiver Module (FG-IR03)
  - CC-MININUSB, Mini USB to PC Cable Adapter (FG5967-20)
- Compatible AMX Products:
  - Enova DGX 8/16/32/64 Digital Media Switchers with ENOVADGX-VO-DXLINK-MMF-S, Enova DGX DXLink Mutimode Fiber Output Board, Simplex (FG1058-633) installed
Power Supply:
- External, Included
  - Each HDMI RX ships with a desktop power supply with power cord 2.5 A at 12 V, Max 13.5 V
Environmental:
- Temperature (Storage): -22° to 158° F (-30° to 70° C)
- Humidity (Operating): 5% to 85% RH (non-condensing)
- Humidity (Storage): 0% to 90% RH (non-condensing)
- Heat Dissipation (On): 65 BTU/hr
Ethernet:
- Ethernet Connection
  - (1) RJ-45, TCP/IP Port (ICS LAN 10/100)
  - Note: Simplex DXLink solutions do not support an Ethernet transport layer on the simplex fiber path, therefore an Ethernet connection is required to provide IR/RS-232/USB Keyboard/Mouse or NetLinx program control to this device
DXLINK FIBER:
- Fiber Connector: LC Duplex conforming to ANSI TIA/EAI 604-10 (FOCIS 10A)
- Note: On the DXLink Mutlimode Simplex Receiver, only the receive portion of the SFP module is active
- Fiber Cable Type: OM3 50/125?m
- Fiber Cable Length: 300m (984 ft)
- Transport Layer Throughput: 10.3125 Gbps
- Fiber Transceiver Type: 10G SFP+
- Optical Wavelength: 850 nm
- Optical Budget:
  - Optical Modulation Amplitude (OMA): -4.3 dBm (min)
  - Optical Modulation Amplitude (OMA) Sensitivity: -11.1 dBm (typ)
- Optical Transceiver Mean: -1 dBm (average power)
HDMI:
- Output Connector: (1) HDMI Type A Female
- Compatible Formats: HDMI, HDCP , DVI
- Signal Type Support: HDMI
- DVI-D (single link with HDMI cable adapter)
- Progressive Resolution Support:
  - All progressive resolutions between 480p and 1920 x 1200 @ 60 Hz via automatic SmartScale query of the display's preferred EDID Detailed Timing Definition
- Interlaced Resolution Support
- Output Scaling: SmartScale or Manual Configuration or Bypass
- 3D Format Support:
  - Yes, if Scaler on RX is set to Bypass mode
  - Frame Packing 1080p 24Hz
  - Frame Packing 720p 50/60Hz
  - Frame Packing 1080i 50/60Hz
  - Top-Bottom 1080p 24Hz
  - Top-Bottom 720p 50/60Hz
  - Side-by-Side Half 1080i 50/60Hz
- Deep Color Support:
  - 30-bit supported when the HDMI Output Board scaler
  - or DXLink RX scaler is in Bypass mode using CEA-861
  - formats and resolution is 1080p60 or less
- Color Space Support:
  - YCbCr 4:4:4 and 4:2:2
  - (Input signal support for YCbCr 4:4:4 and 4:2:2, output
  - color-space is converted to RGB 4:4:4)
- Propagation Delay (Typical): 26 ms when scaling, 5.2 us when in Bypass mode
- CDR (Re-Clocking): Yes
- Output Voltage (Nominal):1.0 Vpp Differential
- Output Rise Time / Fall Time: 425 ps typ (20% - 80%)
- Video Data Rate (Max):
  - 4.95 Gbps / 5.568 Gbps
  - 5.568 Gbps supported when the HDMI Output Board scaler or DXLink RX scaler is in Bypass mode using CEA-861 formats and resolution is 1080p60 or less
  Video Pixel Clock (Max):
  - 165 MHz/185.625 MHz
  - 185.625 MHz supported when the HDMI Output Board scaler or DXLink RX scaler is in Bypass mode using CEA-861 formats and resolution is 1080p60 or less
- Audio Format Support:
  - Dolby TrueHD, Dolby Digital, DTS-HD Master Audio, DTS, 2 CH through 8 CH L-PCM Dolby Digital and DTS support up to 48kHz, 5.1 channels
- Audio Resolution: 16 bit to 24 bit
- Audio Sample Rate: 32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192kHz
- Local Audio Support: Extraction
Analog Audio:
- Output Connections: 3.5mm Mini-Stereo Jack
- Output Signal Types: Stereo Analog
- Output Level (Max): 0 dBU, unbalanced, >= 2 kohms load
- Output Frequency Response: < +0 dB to -0.5 dB, 50 Hz to 20 kHz
- Audio THD+N: <0.04 %, 1 kHz, -10dBu to +2 dBu
- Audio S/N Ratio: >93 dB, 20 Hz to 20 kHz Vin=+2dBu
- Digital to Analog Reference Level:0 dBfs = +0 dBu
- Audio Synchronization:
  - Video formats @ 60Hz frame rate: video formats @ 60Hz frame rate: In scaling mode audio leads video by 12ms typ (4ms to 20ms). In Bypass mode, audio lags video by 14ms
USB (HID) Keyboard & Mouse:
- USB (HID)
  - (1) USB Mini-A/B Connector (“DEVICE”) Connect a keyboard & mouse and send commands to a PC connected to a DXLink Twisted Pair or Fiber TX
Controls:
- ID Pushbutton:
  - Toggle between DHCP and static IP addressing Places system in NetLinx Device ID assignment mode Reset the factory default settings Restore the factory firmware image
- Advanced Configuration Interface: (1) USB Mini-B Connector (“PROGRAM”)
- Serial:
  - (1) 3.5mm Pluggable Phoenix Terminal Block
  - Bidirectional RS-232
  - Standard NetLinx Baudrate 1200-115k Parity support Odd/Even/None
  IR RX:
  - (1) 3.5mm Mini-Stereo Jack
  - Port for IR03 Receiver (Optional)
  IR TX
  - (1) 3.5mm Pluggable Phoenix Terminal Block
  - Port for IR01 Emitter (Optional)
Indicators:
- Power Indicator:
  - (1) LED that lights:
    - Green during normal operation state
    - Red when power is applied and boot sequence is started
    - Yellow when system initialization is in process
- Video Indicator:
  - (1) Green LED indicates the presence of video and audio
  - signals through the module
- Audio Indicator:
  - (1) Green LED indicates the presence of audio signals through the module
- Scaling Button and LEDs:
  - Pushbutton and (3) Green LEDs; use Scaling button to select one of the three options: Bypass, Auto (SmartScale), or Manual. The factory default is Auto (SmartScale). If the RX power cycles, it defaults to the last persisted mode (achieved by pressing scaling button and holding it until the desired scaling mode LED flashes)
- IR TX Indicator: (1) Red LED lights during the transmission of IR data via the rear IR port IR
- RX Indicator: (1) Yellow LED lights during the receipt of IR data via the rear IR port
- RS-232 TX Indicator: (1) Red LED shows serial transmit (TX) data activity
- RS-232 RX Indicator: (1) Yellow LED shows serial receive (RX) data activity
- LINK/ACT:
  - Green LED lights when the Ethernet cable is connected and an active link is established. This LED also blinks when receiving Ethernet data packets
- Status: (1) Green LED lights when the Controller is programmed and communicating properly
- CEC Indicator: Not currently supported
- USB Indicator:
  - (1) Yellow LED lights when either a Keyboard or mouse is connected directly to the RX, or either and/or both are connected to a USB Hub connected to the RX
- ID Pushbutton: Places system in NetLinx Device ID assignment mode
Front Connectors:
- Advanced Configuration Interface
  - (1) USB Mini-B Connector
Back Connectors:
- Local Power: 2.1 mm DC Power Jack
- DXLink Fiber Input: LC Duplex conforming to ANSI TIA/EAI 604-10 (FOCIS 10A)
- ICS LAN/Ethernet Port: RJ-45 Connector, TCP/IP Port (ICS LAN 10/100)
- Serial:
  - 3.5mm Pluggable Phoenix Terminal Block
  - Bidirectional RS-232
  - Standard NetLinx Baudrate 1200-115k
  - Parity support Odd/Even/None
- IR RX: (1) 3.5mm Mini-Stereo Jack Port for IR03 Receiver (Optional)
- IR TX: (1) 3.5mm Pluggable Phoenix Terminal Block Port for IR01 Emitter (Optional)
- USB (HID) Keyboard & Mouse:
  - (1) USB Mini A/B Connector; connect a keyboard & mouse and send commands to a PC connected to a DXLink Twisted Pair or Fiber
- HDMI Output: HDMI Type A Female
- Analog Stereo Output: 3.5mm Mini-Stereo Jack

Input Board 475 kb - Other

Project List

Fiber Receiver 343 kb - Data Sheet

Project List

Fiber Receiver 671 kb - Other

Project List

Fiber Receiver 3878 kb - Other

Project List

Suggested Products

HDMI Over Fiber Receiver

by Crestron Electronics, Inc.

Digital Media 8G Fiber Transmitter 401

by Crestron Electronics, Inc.

DigitalMedia 8G™ Fiber Transmitter 201

by Crestron Electronics, Inc.