Network to Audio Interface
Model: AV-NL2
- Converts two Dante network audio signals to balanced analog
- Selectable Dante sample rates: 44.1khz, 48khz, 88.2khz, 96khz
- Each output switch-selectable for mic or line level
- Normal (-20dBFS) Line-Level Output is +4dBu with 20dB Headroom
- Microphone output level is attenuated 50dB
The AV-NL2 is a line-level interface that converts two Dante network audio channels to two balanced audio outputs on XLR connectors. Each channel provides +4dBu balanced for a network digital audio level of -20dBFS. Each output is equipped with a selector to set the output to line level or attenuate the output by 50 dB to mic level. Special software is not required to configure the module. The AV-NL2 is a professional grade product for studio quality fidelity and low noise performance.
The AV-NL2 may be powered from an external 24Vdc power supply, available separately. The AV-NL2 is equipped to operate from a PoE enabled network switch. The AV-NL2 will reserve power from the switch even while being powered from an external 24Vdc supply. If PoE power and an external 24Vdc supply are both feeding an AV-NL2, the unit will run from the external supply and will seamlessly switch over to PoE power upon loss of the external supply. Valid power and synchronization to the Dante network is indicated by a green LED visible from the front of the unit.
The AV-NL2 is constructed in a durable, professional all-metal enclosure suitable for use on stage or in studio, or mounted to any flat surface. For fixed installations, mounting brackets are included. The chassis is designed to protect the front panel slide switches from accidental damage. This full-featured AV-PAK product is engineered and manufactured in the U.S.A for continuous duty in demanding installations.
- Converts two Dante network audio signals to balanced analog
- Selectable Dante sample rates: 44.1khz, 48khz, 88.2khz, 96khz
- Each output switch-selectable for mic or line level
- Normal (-20dBFS) Line-Level Output is +4dBu with 20dB Headroom
- Microphone output level is attenuated 50dB
- Each output is protected against phantom voltage up to 48Vdc
- Special software not required for module setup
- Exceptional low-noise and low-distortion performance
- High resolution 24 bit digital to analog conversion
- Legendary RDL analog filtering enhances superb audio performance
- Led indicator for valid power and network sync
- Operation from PoE power (class 0, IEEE 802.3af)
- Equipped for Sysflex® rack mounting or surface mounting
- Audio Interface Type - Ethernet Audio
- Dante Enabled - Yes
- Spec Sheet available - Yes
- Operating Temperature (Maximum): 122 F
- Operating Temperature (Minimum): 32 F
- Depth: 5.97 in
- Height: 4.27 in
- Shipping Depth (with packaging): 7 in
- Shipping Height (with packaging): 4.38 in
- Shipping Width (with packaging): 2.25 in
- Width: 4.23 in
- Shipping Weight: 1.39 lbs
- Warranty (Length/Type): 3 Years
- Noise: < -75dB (below +4dBu); < -95 (below +24dBu)
- Network Connector: RJ45 with Link and Speed indicators
- Digital Audio Ethernet Protocol: Dante
- Transmission Rate: 100 Mbps
- Sample Rates supported: 44.1kHz, 48kHz (default), 88.2kHz, 96kHz
- Bit Depth Supported: 24 bits
- Audio Operating Level: -20dBFS = +4dBu
- Reference Level: 0dBFS = +24dBu
- Outputs (2): XLR (male)
- Output Level (operating): +4dBu nominal LINE level balanced; -45dBu nominal MIC level (into 150ohms)
- Output Level (maximum): +24dBu LINE level
- Output Impedance: <100ohms balanced
- Selector per output: Mic/Line
- Frequency Response: 20Hz to 20kHz (± 0.5dB)
- THD+N: <0.1% (20Hz to 20kHz,+4 dBu/-20dBFS); 0.015% at 1kHz (type)
- Crosstalk: Below Noise Floor (1kHz, output to output); < -60 d5dB (20kHz)
- Headroom above +4 dBu/-20 dBFS: 20dB
- Indicators (3): Ethernet Link and Speed (2, rear panel); Sync (front panel)
- Power Requirement: PoE Class 0, IEEE 802.3af
- Specification Conditions: Gain/Level ± 1dB
Suggested Products
Create Spaces
623 S Americana Blvd, Boise, ID 83702
Boise, ID 83702
USA
2083850507
https://createspaces.com/